long necklace of beads original parts

Leisure – Hobbies & Entertainment | | 0 views

New feeling! The original part which is made with the wire

Using the seed beads and the wire, it will try making the original part which has the volume impression.Because it just winds, even with the one which are poor to knit, all right!
* When the terminology which does not understand in the article comes out, beads basic glossary

Because it is the completion which has impact, large texture beads and affinity batsugun!
To gather also popularity, asymmetry in long type.

This time this, is arranged in the cute necklace.Because it is the design which glows in the simple clothes, everyday coordinating becomes pleasant!
As for material and reshipi, in following page!

To following page >

Long necklace material & reshipi which are made with original beads part

Degree of hardness:
Material costs: Approximately 300 Yen * at the time of guide production
Completion size length approximately 86cm * guide size
* () Inside inscription in reshipi

  • Ring part diameter 25mm n/a
  • Seed beads circular small clear AB× white line n/a Proper quantity
  • Plastic cutting beads 12mm clear AB× white line n/a ~ * 1
  • Plastic cutting beads 8mm clear AB× white line n/a ~ * 1
  • Plastic circular ball beads 8mm translucency n/a ~ * 1
  • artistic wire 26issue tinkapa……70cm×5this
  • 9pin 0.7×15mmor more silver……38~this 1
  • round can 0.6×6mm……41~individual
  • round can 0.7×4mm silver……2individual 2
  • kanikan adjuster silver……each1

1…the number may be adjusted to fit the size of their
2…round can0.7×6mmmay substitute a

will be click to enlarge. difficult to discern where, click!

i used the guides, parts such as the left ring. 100i bought yen shop. it does not matter to substitute other things, 2~3mmthere is the thickness of the, beads and wire the same color?, i recommend those of transparency.

wire was used for artistic wire. on strong to rust, will gloss natural finish since it is less. you can also create a wire of other common.

(procedure1) the end of the wire10cmleaving about, winding around the ring wear parts.

(procedure2) through the seed beads onto the wire of the longer. the number may be a suitable, 10individual~20individual is much easier to handle.

(procedure3) winding the wire into the ring parts. first, parts have a ring as shown in the diagram on the left, lift up on the wire. when the wind is to be aware of so that no interval of red beads as much as possible.

tilt the front part of the ring method then, kugura to the wire (they spilled or open interval and facing the bottom bead)
intervals are not as open as possible, hold the beads, it tightens the wire while winding the trick is.
is continued following page to!

< previous page to next page >

long bead necklace made from original parts


(procedure3) continuation beads while maintaining the state is facing up always, wrapped around the ring parts yuku. the middle, if you run out of beads plus, when you are hand packed in the gap. to be aware of as much as possible so that the beads are densely.

because there is a distortion that leaves the larger the number of turns, reshape if necessary.

(procedure4) when nearly round, the inner gap is eliminated as shown in the diagram on the left, the outer gap can only. once in this state, beads through the wire only a few grains.

(procedure5) winding the wire so as to fill the gap in the beads through. further, wound so as to bite several times between the bead wire already wound, fixed.

(procedure6) arranged in the shape of the entire, grasp the tip of the wire pliers, etc., crunch (note that the wire is turned off because there is very strong and draw! ) , turn off the extra wire. the same thing5make one.

(procedure7) cut plastic beads, the round ball beads9put the pin. attaching the pin

(procedure8) (procedure6) parts made of, round can0.6×6mmgive. give you this minute to scoop the beads of a wire.

2each pair is to be2attached to the place (shown on the left) , 2each is preceded by exactly one point, remaining1ko4put in place.
we now have a part in this. after only connect! following page in a hurry to!

< previous page to next page >

long bead necklace made from original parts


the fringe

(procedure9) (procedure7) ~ (procedure8) parts made of, round can0.6×6mmconnect as shown in the diagram on the left is. positions and number of parts, may be changed to suit your taste and size.

part of the necklace

the necklace is part of the tip of the round can0.6×4mmkanikan adjuster and give a.

expanding part of the ring parts1


expanding part of the ring parts2


(completion! ) check the balance with the look, completion.

(arrangement) only individual parts to make a, it also recommended that the pendant.
ring type of seed beads and parts, does not have to be the same as this guide that was used. beads or a mix of several types of, instead of a color for each roll several times, it is also fun to handle border!
< previous page

(related links)

  • attaching the bracket to determine the weave of the gut-
    basic knowledge&technique
  • necklace recipe also recommended in addition to
    • adjust the sum of the plate pendant and beads swallow
    • simple! bead fringe necklace
    • beads recipe: drop (drop) pendant
    • four-leaf motif of beads pendant
    • necklace recipe collection
  • buy the material online
    buy a bead material

< previous page

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

  • cut plastic beads12mm

  • cut plastic beads8mm

  • round plastic ball beads8mm

  • round can

upper stage: from the left edge

parts parts parts

lower: from the left edge

parts parts parts

< back to main

  • cut plastic beads12mm

  • cut plastic beads8mm

  • round plastic ball beads8mm

  • round can

upper stage: from the left edge

kanikan parts

lower: from the left edge

adjuster parts

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main

< back to main


Additional items from "Leisure – Hobbies & Entertainment"