2the title of the line1line fit to2ways

To store the title which divides into 2 lines to 1 lines?

When making the title of the document, there is no experience where title extends over 2 lines probably will be?Especially, when just several letters remaining in 2nd line, if it is possible, those which we would like to store to 1 lines.The following picture is such an example.When 2 letters “of lecture” can be inserted in 1st line, it will be clear, don’t you think?.

2 letters protruding to the following line, title has been recognized into 2 lines

The measure which comes to mind directly is the following two.

• Method 1: Shaving the letter of title, it makes short.
• Method 2: Letter size of title is made small.

Shaving letter, if there is no problem, perhaps method 1 the best.Or, if it is possible to make letter size small, also method 2 probably is proper.However, because it is the title which with special care is thought through we would not like to change when and, letter size is changed, can be also a case that layout balance deteriorates, sufficiently.

Those where this time it introduces are another method such time of being useful.Concretely it is the following two.

• Method 3: Breadth of individual letter is shortened a little.
• Method 4: It shortens between letter.

Speaking strictly, method 3 is one of the variation of the method of changing letter size, but please refer with the notion that where it is also such method.

it should be noted, screenWord 2010use. the methodWord 2010/2007are common to nearly, Word 2003is slightly different. where the operation is different, supplements as appropriate.

> individualshrink the width of the character of1line fit to

individualshrink the width of the character of1line fit to

in, let me introduce a little from how to reduce the width of the character. to be more specific, individualyou can specify percent shrink the width of the character of.

1.select the entire character of the title.
2. [home] of tab [paragraph] in [the extended format] click the button (Word 2003in [formatting] on the toolbar [expansion of the character/reduction] of button [ ] click) .
3. [expansion of the character/reduction] from the sub-menu of [90%] select the.

after you select the entire character of the title, [home] of tab [paragraph] in [the extended format] click the button, [expansion of the character/reduction] from the sub-menu of [90%] select the

4.1one1the standard width of one character90%will, the title1was contained in line.

1one1the standard width of one character90%will, the title1was contained in line

> shorten the interval between characters and character1line fit to

shorten the interval between characters and character1line fit to

the following characters and character spacing (between the characters) to shorten the1is how to fit the line. does not change the font size, characters and character will be feeling stick.

1.select the entire character of the title.
2. [home] of tab [font] click the button at the bottom right of the group (Word 2003in [format] [font] select the) .

after you select the entire character of the title, [home] of tab [font] click the button at the bottom right of the group

3. [font] dialog box that appears, [advanced] of tab [character spacing] in [narrowly] select the (Word 2007/2003in [font] of the dialog box [character width and spacing] tab) . its right next to [interval] if you increase the number in, it is also possible to more narrowly. the initial configuration 1pt does not work when de-, please try to increase the number of.
4. [OK] click the button.

[font] dialog box that appears, [advanced] of tab [character spacing] in [narrowly] select the [OK] click the button

5.stuffed between the characters is, the title1was contained in line.

stuffed between the characters is, the title1was contained in line

how to1character will be long and slender point, how to2is [interval] depending on the value of demerit points is character and character overlap, the title1if you use the line fit for the purpose, you can easily take advantage of both. please try by all means.